Коды ошибок в PC
Добавлено: 17:41 - 12.02.10Коды ошибок в PC
C No problem. Means that the machine is correcting the fuser film tracking
CC Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier
E000 Low fuser temperature
E001 High fuser temperature
E002 High fuser temperature
E003 Erratic fuser temperature
E007 Fuser film off track and will not repair itself
E010 Main drive problem
E030 Counter problem
E064 Scan problem, or power supply
E202 Scan problem
E210 Lens drive problem or lens sensor
E220 Exposure lamp stays on or off
E240 DC controller (main board) or composite power supply
E261 Zero cross problem. Power frequency or composite power supply
E400 Communication problem between boards
E803 24 volt problem
EO Fuser problem
H Fuser overheat
E000 Fuser thermistor, heater, thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac
E004 Triac or fuser won't shut off
E007 Fuser film is off center or not driving properly
E010 Main motor drive problem
E030 Counter
E064 Composite power supply or main board
E202 Scan problem
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply
E261 Composite power supply or fluctuating power
E400 ADF communication problem to machine
E402 ADF belt motor drive
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem
E510 Sorter drive problem
E530 Stapler guide bar motor
E531 Stapler swing motor
E540 Bin shift motor
E541 Bin motor drive problem
E710 Main board
E711 Main board
E712 Main board or communication problem with ADF
E717 Main board, asst. board
U0 Initializing. Sets all user modes to factory default settings
U1 Auto clear timer. Range 1-9. Each digit=1 minute
U2 Automatic power shut off timer
U3 Fine adjustment of zoom
U4 Auto cassette switching
U5 Sort or non-sort default
U6 Cleans document feeder pickup assembly
U7 CLEAR "replace drum"
U9 Auto exposure or manual exposure as default
EO Heater problem
E1 The heater film has gone off center. Turn machine off & on, make sure it's level etc
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
E000 Fuser problem
E001 Fuser problem
E010 Drive
E210 Zoom/lens/motor problem
E00 Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20 seconds
E001 Shorted thermistor or high-temperature, Exit sensor
E010 Clock Pulse
E210 Zoom Lens Problem
C No problem. Means that the machine is correcting the fuser film tracking
CC Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier
E000 Low fuser temperature
E001 High fuser temperature
E002 High fuser temperature
E003 Erratic fuser temperature
E007 Fuser film off track and will not repair itself
E010 Main drive problem
E030 Counter problem
E064 Scan problem, or power supply
E202 Scan problem
E210 Lens drive problem or lens sensor
E220 Exposure lamp stays on or off
E240 DC controller (main board) or composite power supply
E261 Zero cross problem. Power frequency or composite power supply
E400 Communication problem between boards
E803 24 volt problem
EO Fuser problem
H Fuser overheat
E000 Fuser thermistor, heater, thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac
E004 Triac or fuser won't shut off
E007 Fuser film is off center or not driving properly
E010 Main motor drive problem
E030 Counter
E064 Composite power supply or main board
E202 Scan problem
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply
E261 Composite power supply or fluctuating power
E400 ADF communication problem to machine
E402 ADF belt motor drive
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem
E510 Sorter drive problem
E530 Stapler guide bar motor
E531 Stapler swing motor
E540 Bin shift motor
E541 Bin motor drive problem
E710 Main board
E711 Main board
E712 Main board or communication problem with ADF
E717 Main board, asst. board
U0 Initializing. Sets all user modes to factory default settings
U1 Auto clear timer. Range 1-9. Each digit=1 minute
U2 Automatic power shut off timer
U3 Fine adjustment of zoom
U4 Auto cassette switching
U5 Sort or non-sort default
U6 Cleans document feeder pickup assembly
U7 CLEAR "replace drum"
U9 Auto exposure or manual exposure as default
EO Heater problem
E1 The heater film has gone off center. Turn machine off & on, make sure it's level etc
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
E000 Fuser problem
E001 Fuser problem
E010 Drive
E210 Zoom/lens/motor problem
E00 Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20 seconds
E001 Shorted thermistor or high-temperature, Exit sensor
E010 Clock Pulse
E210 Zoom Lens Problem