• Реклама
 

Коды ошибок в HP LJ 1160,1320

Коды ошибок в HP LJ 1160,1320

Непрочитанное сообщение Сервис-центр СКАН » 10:59 - 28.11.12

HP LJ 1160,1320

На данных моделях аппаратов индикация осуществляется при помощи 5 индикаторов, по порядку сверху вниз:
1.Wireless light - обозначим как "1"
2.Toner light - обозначим как "2"
3.Attention light - обозначим как "3"
4.Ready light - обозначим как "4"
5.Go button and ligh - обозначим как "5"

Рассмотрим индикации данных моделей и их вторичные индикации ошибок:

1 индикация
1 - не горит
2 - не горит
3 - мигает
4 - мигает (индикаторы мигают поочереди)
5 - мигает
Initialization/Startup/Reconfiguration initialization/Job cancel. Cleaning page.
2 индикация
1 - не горит
2 - не горит
3 - не горит
4 - горит
5 - не горит
Ready
3 индикация
1 - не горит
2 - не горит
3 - не горит
4 - мигает
5 - не горит
Processing data
4 индикация
1 - не горит
2 - не горит
3 - мигает
4 - не горит
5 - горит
Manual feed or continuable error: manual feed, out of paper for the specified tray, general continuable error, memory configuration error, personality/Job related error. To recover from the error and print whatever data is possible, press the Go button. The printer might print a partial page, or the quality might be lower than normal. If the page is too complex, the printer might be out of memory. Try reducing the complexity of the page or try adding more memory. If the recovery is successful, the printer goes to the Processing Data state and completes the job. If the recovery is unsuccessful, the printer returns to the Continuable Error state.
5 индикация
1 - не горит
2 - не горит
3 - мигает
4 - не горит
5 - не горит
Attention: paper tray is empty, door open, paper jam, misfeed from tray.erif that the print cartridge is present and that the print-cartridge door is closed correctly. Verify that media is present in the input tray. Clear any jams and perform paper-path functional checks. To reset the printer after a jam, press the Go button. You might need to clear the error manually, and press the Go button or close the top cover.
6 индикация
1 - не горит
2 - не горит
3 - горит
4 - горит
5 - горит
Fatal error: A fatal error has occurred. The Attention, Ready, and GO LEDs are on solid. Turn off the printer, wait 10 seconds, and turn on the printer. Unplug the printer for five minutes, and then plug it back in and turn it on. If you are unable to resolve the problem, Contact HP support .
7 индикация
1 - не горит
2 - не горит
3 - мигает
4 - мигает (индикаторы мигают одновременно)
5 - мигает
Accessory error: Нажмите и удерживайте кнопку GO, чтобы получить подкод ошибки:
1 подкод
1 - не горит
2 - не горит
3 - горит
4 - не горит
5 - не горит
Engine error : The formatter and engine are not communicating. Unplug the printer and then plug it back in. Reseat the formatter cable in the ECU. If the error persists, replace the formatter. If, after replacing the formatter, the error persists, replace the ECU.
2 подкод
1 - не горит
2 - не горит
3 - не горит
4 - горит
5 - не горит
Laser/scanner error: Check the laser/scanner cable connections. If the error persists, replace the laser/scanner.
3 подкод
1 - не горит
2 - не горит
3 - мигает
4 - не горит
5 - горит
Beam error: Check the laser/scanner cable connections. If the error persists, replace the laser/scanner.
4 подкод
1 - не горит
2 - не горит
3 - мигает
4 - не горит
5 - не горит
Motor error: Check the motor cable connections. If the error persists, replace the motor.
5 подкод
1 - не горит
2 - не горит
3 - не горит
4 - горит
5 - горит
Fuser error : Unplug the printer for at least ten minutes. Verify that the fuser connector and thermistor connector are both firmly seated in the ECU. Perform a heating element resistance check. If the resistance readings are correct, but the error persists, replace the fuser.
6 подкод
1 - не горит
2 - не горит
3 - мигает
4 - мигает (индикаторы мигают одновременно)
5 - мигает
General fatal error: Turn the printer off, and then turn the printer back on. If the error persists, disconnect the I/O cable and print an engine test. If the self-test is successful, reconnect the I/O cable. If the error persists, replace the formatter.
Аватара пользователя
Сервис-центр СКАН
Помощник админа Консультант
 
Сообщения: 966
Зарегистрирован: 14:11 - 28.02.05
Откуда: Москва, м. Таганская
Баллы репутации: 1

Вернуться в Коды и сброс ошибок в HP

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 1

  • Реклама