• Реклама
 

Коды ошибок для Toshiba

Коды ошибок для Toshiba

Непрочитанное сообщение Сервис-центр СКАН » 14:38 - 03.03.10

Toshiba 1210
C1 Copy table position error
C2 Paper is not fed from the tray when the copy table starts moving
C3 Copy table drive error
C4 Copy table position error
C5 Copy table end position error
C6 Copy table position error at the end of the copy cycle
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8 Thermofuse blown
CP Main drive overloaded
CA Main Board defective
E1 Paper jam
E2 Fuser jam
E3 Paper jam at start-up
E5 Paper jam in the tray
E7 Paper jam in the registration area


Toshiba 1310
C5 Copy table drive overloaded
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CE EPROM defective or missing
CP Main drive overloaded
CD EPROM end of life
CF Development unit not properly installed or defective
E0 Used toner collection bottle full
E1 Paper jam
E2 Fuser jam
E3 Paper jam at start-up
E5 Paper jam in the tray
E6 Paper jam at by-pass or defective sensor


Toshiba 1340, 1350
C5, C6 Scan problem
C7 Fuser problem (reset with 0 + 8 mode, code 89)
CE Missing EEPROM
CF Board problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E5 Paper feed jam
E0 Toner waste bottle is full


Toshiba 1550
C01 Main motor drive problem
C21 Optics problem Scan , lens, mirror
C26 Exposure lamp detect problem
C32 Setup error (UA)
C41 Fuser thermistor, or no heat
C43 Fuser thermistor problem or other fuser problem, after machine goes into ready
C44 Heater problem
C54 Communication problem between sorter and machine main board
C55 Communication problem between ADF and machine main board
C71 ADF drive problem
C72 ADF registration sensor problem
C73 EEPROM initialization problem
C81 Sorter paper conveying motor
C82 Sorter bin motor
C83 Sorter upper sensor
C84 Sorter lower sensor
C85 Sorter home sensor
C86 Sorter copy removal sensor
C94 Optics initialization problem in test modes
E01 Paper jam
E02 Fuser jam
E03 Paper jam at startup
E05 Paper jam in the registration area
E14 Lower cassette jam
E71, E72, E73 ADF jam
E75 ADF jam of 2nd original
E81, E82 Sorter jam


Toshiba 1560
C01 Main motor drive overloaded
C21 Optics problem Scan , lens, mirror
C26 Exposure lamp blown, or bad contacts
C32 Easy set-up error
C41 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C43, C44 Abnormal temperature in the fuser, thermistor error
C54 Communication with the sorter is intrerrupted
C55 Communication with the feeder is intrerrupted
C71 Top Feeder motor overloaded
C72 Sensor problem in the feeder
C73 Feeder EPROM initialization error
C81 Sorter paper transport motor overloaded
C82 Sorter shift tray motor overloaded
C83 Upper position error in the sorter
C84 Lower limit position error in the sorter
C85 Home position error in sorter
C88 Paper sensor error in sorter
C94 Optical system initialization error
E01 Paper jam
E02 Fuser jam
E03 Paper jam at startup
E05 Paper jam in the registration area
E14 Paper jam in the Paper Feed Unit
E71 Original jammed in the top feeder
E72 Original jammed during transport in the top feeder
E73 Original jam at the feeder exit
E75 Original jammed
E81, E82 Sorter jam


Toshiba 1650
A4 Sorter problem
A5 Communication problem between main CPU and IPC
A6 Sorter interface problem
C2 Communication problem between CPU's
C5 Scan or optic problem. Locked up or won't initialize or return to home position
C7 Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CF Developer calibration problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E4 Front door opened during copy cycle
E5 Paper feed jam


Toshiba 1710
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam


Toshiba 2050
A4 Sorter problem
A5 Communication problem between main CPU and IPC
A6 Sorter interface problem
C2 Communication problem between CPU's
C5 Scan or optic problem. Locked up or won't initialize or return to home position
C7 Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CF Developer calibration problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E4 Front door opened during copy cycle
E5 Paper feed jam


Toshiba 2060
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter


Toshiba 2310
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam


Toshiba 2500
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam


Toshiba 2510
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam


Toshiba 2532
A4 Sorter problem
A5 Communication problem with main board
A6 Communication problem with sorter
A7 Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2 Communication problem between main board
C5 Scan won't initialize or won't move
C7 Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CC ADF belt motor or exit motor not turning
CF Auto toner adjustment did not take
CP Drive problem in machine
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy cycle
E5 Feed jam


Toshiba 2540
A4 Sorter problem
A5 Communication problem with main board
A6 Communication problem with sorter
A7 Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2 Communication problem between main board
C5 Scan won't initialize or won't move
C7 Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CC ADF belt motor or exit motor not turning
CF Auto toner adjustment did not take
CP Drive problem in machine
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy cycle
E5 Feed jam


Toshiba 2550
A2 Duplex functional problems
A4 Sorter problem
A5 Communication lost with the sorter
A6 Communication problems with the sorter interface
A7 Communication problems with the feeder
A9 Exposure lamp blown, or bad contacts
C2, C3 Processor to subprocessor communication problems
C5 Optical system initialization error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CB Original feed motor overloaded in the feeder
CC Original transport motor overloaded in the feeder
CF Toner density error
CP Main motor drive overloaded
E1 Paper jam detected in machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E4 Front cover open during copy cicle
E5 Paper feed jam in the paper tray
E8 Paper jam in the duplex unit
E9 Paper jam in the optional paper feed unit
EC Original misfeed in the feeder
ED Original jam in the feeder
EE Original jam at the feeder inverter or exit area


Toshiba 2810
C1 Scan did not return home
C3 Scan home sensor
C4 Scan problem
C5 Scan limit sensor
C6 Scan did not return
C7 Thermistor or other fuser problem
CC Scan did not leave home
CP Drive
E1 Jam inside machine
E2 Fuser jam or exit jam
E3 Exit switch or registration switch
E5 Paper feed jam
E7 Cassette or registration jam


Toshiba 2860
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter


Toshiba 2870
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter


Toshiba 3110
C1 Copy table start-up position error
C2 The paper does not feed when the copy table starts moving
C3 Paper start position not detected, copy table switch defective
C4 Copy table home position error
C5 Copy table end position error
C6 Copy table reverse movement error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CP Main motor drive overloaded
E1 Paper jam in the machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E5 Paper jam in the paper tray
E6 Paper jam at by-pass or defective sensor
E7 Paper jam in the feed area or registration



Toshiba 3210
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2, C3 Processor to subprocessor communication problems
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam


Toshiba 3220
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam


Toshiba 3301
C1 Copy table start-up position error
C2 The paper does not feed when the copy table starts moving
C3 Paper start position not detected, copy table switch defective
C4 Copy table home position error
C5 Copy table end position error
C6 Copy table reverse movement error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CP Main motor drive overloaded
E1 Paper jam in the machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E5 Paper jam in the paper tray
E6 Paper jam at by-pass or defective sensor
E7 Paper jam in the feed area or registration


Toshiba 3550
A1 Transfer/separator
A2 Duplex problem
A3 PFC CPU malfunction
A4 Sorter problem
A5 Communication problem between main board and IPC
A6 Sorter board to copier communication problem
A7 Communication problem between copier and RADF
A0 Communication main board problem
C3 Communication problem between main board and sub processor
C5 Optics locked or not initialized
C7 Fuser problem. Reset required. Turn off power. Hold "0" & "8" keys while turning on power. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the number keys, press "0". Then press "interrupt". Then press "0" & "9" at the same time
CB ADF feed motor drive problem
CC ADF transport motor drive problem
CP Copier main motor drive problem
E1 Jam
E2 Fuser jam
E3 Jam at turn on
E4 Front door opened during copy cycle
E5 Registration jam
E8 Duplex unit jam
E9 Jam in paper feed unit pedistal
EC ADF jam
ED ADF transport jam
EE ADF exit or reversing jam


Toshiba 3560
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter


Toshiba 3570
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter


Toshiba 3701
E0 Paper jammed in the machine at power-up
E1 Paper jam in the fusing or transport area
E2 Paper jam in the fusing area
E3 Misfeed at the manual feed table
E6, E7, E8 Copy table drive problem
E9 Copy table reverse clutch not working


Toshiba 3810
C5 Scan problem
C7 Heater problem
CD EEPROM at end of life
CE EEPROM/main board problem
CF DV unit out or toner sensor problem
CP Drive
E1 Paper jam before exit
E2 Exit jam
E3 Jam
E5 Cassette jam
E6 Bypass jam
E0 Waste toner full


Toshiba 3910
C5 Scan problem
C7 Heater problem
CD EEPROM at end of life
CE EEPROM/main board problem
CF DV unit out or toner sensor problem
CP Drive
E1 Paper jam before exit
E2 Exit jam
E3 Jam
E5 Cassette jam
E6 Bypass jam
E0 Waste toner full


Toshiba 4010
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam


Toshiba 4111, 4121
C1 Scanner not home
C2 First paper path switch or sub processor
C5 Scan stop switch
C5 Scan won't stop
C7 Fuser problem
C8 Lens
C9 Check 24V


Toshiba 4130, 4140
C1 Copy table reverse movement home position error
C2 Paper start position not detected, copy table switch defective
C5 Copy table end position error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8 Lens home position error
C9 5v power supply defective
E1 Paper jam detected in machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E5 Paper feed jam in the paper tray
E7 Paper jam at registration


Toshiba 4501
E0 Paper jammed in the machine at power-up
E1 Paper jam in the fusing or transport area
E2 Paper jam in the fusing area
E3 Misfeed at the manual feed table
E6, E7, E8 Copy table drive problem
E9 Copy table reverse clutch not working


Toshiba 4550
A2 Duplex functional problems
A4 Sorter problems
A5 Communication lost with the sorter
A6 Communication problems with the sorter interface
A7 Communication problems with the feeder
A9 Exposure lamp blown, or bad contacts
C2, C3 Processor to subprocessor communication problems
C5 Optical system initialization error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CB Original feed motor overloaded in the feeder
CC Original transport motor overloaded in the feeder
CF Toner density error
CP Main motor drive overloaded
E1 Paper jam detected in machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E4 Front cover open during copy cicle
E5 Paper feed jam in the paper tray
E8 Paper jam in the duplex unit
E9 Paper jam in the optional paper feed unit
EC Original misfeed in the feeder
ED Original jam in the feeder
EE Original jam at the feeder inverter or exit area


Toshiba 4560
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter


Toshiba 4570
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem
C11 Duplex exit motor
C12 Duplex end motor
C13 Upper cassette
C14 Lower cassette
C15 Pedestal upper cassette
C16 Pedestal middle cassette
C17 Pedestal lower cassette
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41 Fuser thermistor or low temperature
C43 Fuser problem after warm-up
C44 Fuser problem after warm-up
C45 Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter


Toshiba 4810
C1 Scan not home
C2 Scan did not leave home
C3 Forward scan
C4 Forward scan (dual page mode)
C5 Scan limit
C6 Scan return
C7 Thermistor
CP Motor lock
E1 Fuser jam
E2 Exit jam
E3 Jam
E5, E7 PF jam


Toshiba 4910
C4 Cam switch
C5 Optics
C7 Thermistor or fuser
C8 Scan motor stays on
CE Main board
C0 Dead battery
CP Drive
E1 Jam
E2 Fuser jam
E3 Jam at turn on
E4 Door opened during copy run


Toshiba 5010
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC, ED ADF jam
EE ADF exit/reverse jam


Toshiba 5020
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
A0 Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won't shut off
CA Main board problem
CB, CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC, ED ADF jam
EE ADF exit/reverse jam


Toshiba 5110
C0 Selector motor problems
C2, C3 Processor to subprocessor communication problems
C4 Paper feed cam motor drive problems
C5 Optic system initialization error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8 Scanner motor drive problems
CD EPROM end of life
CE EPROM defective or missing
CF Development unit not properly installed or defective
CP Main motor drive overloaded
E0 Used toner collection bottle full
E1 Paper jam in the machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E4 Front cover open during the copy cycle
E5 Cassette jam
E6 Paper jam at by-pass or defective sensor


Toshiba 5120
C2 Signal to sub processor
C4 Cam motor
C5 Optics
C7 Thermistor or fuser problem
CD Weak battery
CE Battery disconnected
C0 DV select problem
CP Drive
E1 Jam
E2 Fuser jam
E3 Jam after turning on
E4 Door opened during run
E5 Lower cassette jam
E6 Upper cassette


Toshiba 5510
C2 Signal to sub processor
C4 Cam motor
C5 Optics
C7 Thermistor or fuser problem
CD Weak battery
CE Battery disconnected
C0 DV select problem
CP Drive
E1 Jam
E2 Fuser jam
E3 Jam after turning on
E4 Door opened during run
E5 Lower cassette jam
E6 Upper cassette


Toshiba 5511
C5 Initializing
C6 Home switch
C7 Thermistor
C8 Scan motor on
C9 Scan problem
E0 Waste toner bag full
E1 Jam
E2 Fuser jam
E3 Exit jam
E4 Front door


Toshiba 5540
A0 Abnormal signal received at the optional paper feed tray
A1 Charge corona cleaner error
A2 Duplex functional problems
A3 Paper feed controller problems
A4 Sorter problem
A5 Communication lost with the sorter
A6 Communication problems with the sorter interface
A7 Communication problems with the feeder
A9 Exposure lamp blown, or bad contacts
C2, C3 Processor to subprocessor communication problems
C5 Optic system initialization error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CB Original feed motor overloaded in the feeder
CC Original transport motor overloaded in the feeder
CE BC RAM firmware problems
CF Toner density error
CP Main motor drive overloaded
E0 Used toner collection bottle full
E1 Paper jam in the machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E4 Front cover open during the copy cycle
E5 Paper feed jam in the paper tray
E8 Paper jam in the duplex unit
E9 Paper jam in the optional paper feed unit
EC Original misfeed in the feeder
ED Original jam in the feeder
EE Original jam at the feeder inverter or exit area


Toshiba 5610, 5620
C0 DV select switch or motor problem
C1-C4 Signal from sub processor (motor control board)
C5 Optics
C6 Home sensor
C7 Fuser
C8 Scan
CA Sub processor
CD Weak battery
CE Battery disconnected
CP Main motor


Toshiba 5910
C2, C3 Processor to subprocessor communication problems
C4 Paper feed cam motor drive problems
C5 Optic system initialization error
C7 Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8 Scanner motor drive problems
CD EPROM end of life
CE EPROM defective or missing
CF Development unit not properly installed or defective
CP Main motor drive overloaded
E0 Used toner collection bottle full
E1 Paper jam in the machine
E2 Paper jam in the fusing area
E3 Paper jam at start-up
E4 Front cover open during the copy cycle
E5 Cassette jam
E6 Paper jam at by-pass or defective sensor
E7 Paper jam in the machine
Аватара пользователя
Сервис-центр СКАН
Помощник админа Консультант
 
Сообщения: 966
Зарегистрирован: 14:11 - 28.02.05
Откуда: Москва, м. Таганская

Вернуться в Коды ошибок и их сброс

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 1

  • Реклама
cron