• Реклама
 

Матричный принтер Epson DFX 8500 - настройка alpha и betta

Матричный принтер Epson DFX 8500 - настройка alpha и betta

Непрочитанное сообщение wwd » 14:55 - 22.06.05

Как настроить Alpha и Betta в этом принтере. Заранее спасибо.
wwd
 

Непрочитанное сообщение dobrik » 16:08 - 13.01.06

Настройка параметров A/B EPSON DFX8500

Rev. B 4-13
Step 1: Remove the paper, ribbon cartridge, and ribbon mask holder from the printer. Then confirm the

ALPHA value written on the print head nose.

Step 2: Close the top cover.
ALPHA Value Write Mode :
Step 3: Turn the printer on while pressing the Tear Off, Micro Feed (v), and Front/Rear switches. At this
time the printer performs PG home position seek. and the carriage moves to the 15 column.
Step 4: The panel indicates the current ALPHA adjustment value (Refer to Table 4-1.).
Step 5: Write the ALPHA value written on the print head into the memory.
•Press the Micro Feed (v) switch to increment value by +1.
•Press the Micro Feed (^) switch to decrement the value by -1.
Step 6: 1) When you finish the adjustment (such as you have replaced the print head.), press the LF/FF
Load SW, then the ALPHA value is written to the EEPROM and finish the adjustment mode.
Then turn the power off and install the ribbon mask holder and the ribbon cartridge.
2) When you continue the BETA values write operation, press the Pause SW, then the ALPHA
value is written to the EEPROM and enter to the BETA values write mode.
BETA Values Write Mode :
Step 7: Open the top cover and inset the 0.43 mm thickness gauge into the space between the platen
and the print head nose. (At this time, never shift the print head. If done it, return to Step 3.)
Step 8: Contact the tension gauge to the hole of the thickness gauge and pull it straight to the right.
Step 9: Hold the thickness gauge gradually with the print head nose by pressing the below switch.
•Press the Micro Feed (v) switch to increment value by +1.
•Press the Micro Feed (^) switch to decrement the value by -1.
The panel indicates the current BETA3’ adjustment value (Refer to Table 4-1.).
Step 10: Set the BETA3’ value when the tension gauge indicates the 150 (135 - 165) gf, the tension gauge
can move to right in a degree.
Step 11: After complete BETA3’ adjustment, press Pause SW to enter next step.
Step 12: Close the print head nose to the platen by pressing the below switch.
•Press the Micro Feed (v) switch to increment value by +1.
•Press the Micro Feed (^) switch to decrement the value by -1
The panel indicates the current BETA2 adjustment value (Refer to Table 4-1.).
Step 13: After complete BETA2 adjustment, press Pause SW to enter next step.
Step 14: Inset the 0.43 mm thickness gauge into the space between the platen and the print head nose.
Step 15: Hold the thickness gauge gradually with the print head nose by pressing the below switch.
•Press the Micro Feed (v) switch to increment value by +1.
•Press the Micro Feed (^) switch to decrement the value by -1.
The panel indicates the current BETA3 adjustment value (Refer to Table 4-1.).
Step 16: After complete BETA3 adjustment, press Pause SW to enter next step.
Step 17: Inset the 0.80 mm thickness gauge into the space between the platen and the print head nose.
Step 18: Hold the thickness gauge gradually with the print head nose by pressing the below switch.
•Press the Micro Feed (v) switch to increment value by +1.
•Press the Micro Feed (^) switch to decrement the value by -1.
The panel indicates the current BETA4 adjustment value (Refer to Table 4-1.).
Step 19: After complete BETA4 adjustment, press Pause SW then all of measured BETA values written
to the EEPROM, and turn the printer power off.
Note: When either the measured BETA values (BETA2, BETA3, and BETA4) are out of range
(Refer to Table 4-1.) or the below formula is not satisfied, the printer sounds five beeps
and not written the values to the EEPROM.
Formula: A1 = 0.43 / (BETA3 - BETA2) and 0.0134 < A1 < 0.0187
A2 = (0.80 - 0.43) / (BETA4 -BETA3) and 0.0115 < A2 < 0.0195
Step 20: Install the ribbon mask holder and the ribbon cartridge.
dobrik
 

Непрочитанное сообщение printmechanic » 17:44 - 14.01.06

alfa - цифира на голове красным цветом,
betta - под картриджем
все остальное в servis manual, ЭТО ДЕЛО ОЧЕНЬ ТОНКОЕ - МОЖНО ПОПАСТЬ НА $$$,00
Аватара пользователя
printmechanic
Консультант
 
Сообщения: 618
Зарегистрирован: 13:20 - 13.01.06
Откуда: Москва
Баллы репутации: 0

Непрочитанное сообщение wwd » 10:50 - 19.01.06

Всем огромное спасибо!
wwd
 


Вернуться в EPSON

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 5

  • Реклама