samsung 2165w дебаг
Добавлено: 09:59 - 11.10.13Здраствуйте! принтер сдох после fix прошивки.
Пытаюсь восстановить дебаг кабелем, но выдает ошибку!
Вот лог терминала:
firmware source address : 0x41800000
firmware address to be written : 0x02320022
firmware size : 0x10111101
main : 0x20020200
sub : 0x10110011
image : 0x00022222
image reserved : 0x01111081
Can not find sig
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
Loading Kernel...
New kernel was found...
checksum is not valid(original = 0x0000A5A5, calculated = 0x0000D057)
Run Firmware Upgrade Mode...
Flash Data Download Address : 0x41800000
===============================
Start flash_writer
===============================
firmware source address : 0x41800000
firmware address to be written : 0x00000000
firmware size : 0x00000000
main : 0x00000000
sub : 0x00000000
image : 0x00000000
image reserved : 0x00000000
Can not find sig
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x41800000)
-------------------------
Link ID : [4F54281A]
-------------------------
USB download<HS><HS>
firmware source address : 0x41800000
firmware address to be written : 0x02220022
firmware size : 0x10111101
main : 0x20020200
sub : 0x10110011
image : 0x00022222
image reserved : 0x01111081
Can not find sig
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
<CPU:300Mhz RAM:100Mhz SysClk:100Mhz >
----------------------------------------------------------------
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
Version : BLUEJAY-W SEC Ver.0.10 2011-09-21
----------------------------------------------------------------
Do you want to download from external port?[N] : n
pROBE+> fl
Run Firmware Upgrade Mode...
Flash Data Download Address : 0x41800000
===============================
Start flash_writer
===============================
firmware source address : 0x41800000
firmware address to be written : 0x00000000
firmware size : 0x00000000
main : 0x00000000
sub : 0x00000000
image : 0x00000000
image reserved : 0x00000000
Can not find sig
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x41800000)
-------------------------
Link ID : [4F54281A]
-------------------------
USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 92 bytes
[[6422648 Bytes received]] - Complete Downloading
} /* Download End */
firmware source address : 0x4180001C
firmware address to be written : 0x00000000
firmware size : 0x00620000
main : 0x03000059
sub : 0x00030002
image : 0x00000000
image reserved : 0x00000000
checksum is valid
ul_start_addr = 00000000, ul_end_addr = 00620000
Boot image!
Found new kernel(0x4184001C)!!!!
[ZLIB ERROR]The compressed data are corrupted or incomplete!!!
This is NOT valid image.!!!!
Not found new kernel!!!!
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
Пытаюсь восстановить дебаг кабелем, но выдает ошибку!
Вот лог терминала:
firmware source address : 0x41800000
firmware address to be written : 0x02320022
firmware size : 0x10111101
main : 0x20020200
sub : 0x10110011
image : 0x00022222
image reserved : 0x01111081
Can not find sig
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
Loading Kernel...
New kernel was found...
checksum is not valid(original = 0x0000A5A5, calculated = 0x0000D057)
Run Firmware Upgrade Mode...
Flash Data Download Address : 0x41800000
===============================
Start flash_writer
===============================
firmware source address : 0x41800000
firmware address to be written : 0x00000000
firmware size : 0x00000000
main : 0x00000000
sub : 0x00000000
image : 0x00000000
image reserved : 0x00000000
Can not find sig
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x41800000)
-------------------------
Link ID : [4F54281A]
-------------------------
USB download<HS><HS>
firmware source address : 0x41800000
firmware address to be written : 0x02220022
firmware size : 0x10111101
main : 0x20020200
sub : 0x10110011
image : 0x00022222
image reserved : 0x01111081
Can not find sig
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
<CPU:300Mhz RAM:100Mhz SysClk:100Mhz >
----------------------------------------------------------------
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
Version : BLUEJAY-W SEC Ver.0.10 2011-09-21
----------------------------------------------------------------
Do you want to download from external port?[N] : n
pROBE+> fl
Run Firmware Upgrade Mode...
Flash Data Download Address : 0x41800000
===============================
Start flash_writer
===============================
firmware source address : 0x41800000
firmware address to be written : 0x00000000
firmware size : 0x00000000
main : 0x00000000
sub : 0x00000000
image : 0x00000000
image reserved : 0x00000000
Can not find sig
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x41800000)
-------------------------
Link ID : [4F54281A]
-------------------------
USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 92 bytes
[[6422648 Bytes received]] - Complete Downloading
} /* Download End */
firmware source address : 0x4180001C
firmware address to be written : 0x00000000
firmware size : 0x00620000
main : 0x03000059
sub : 0x00030002
image : 0x00000000
image reserved : 0x00000000
checksum is valid
ul_start_addr = 00000000, ul_end_addr = 00620000
Boot image!
Found new kernel(0x4184001C)!!!!
[ZLIB ERROR]The compressed data are corrupted or incomplete!!!
This is NOT valid image.!!!!
Not found new kernel!!!!
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again